Single Road WN8-JGQQ-switched Laser Power Supply-IPL power supply

Add to cart

Warm prompt: Transition photoelectric sold commodities all pass strict supplier qualification review, review shipment, warehouse full inspection, full inspection process. Change the packing because some goods manufacturer, different batch, different production date, production plants, and so on and so forth, tiny differences lead to physical goods and pictures, so please you to receive goods kind prevail, at the same time we will try to be updated, thus bring you inconvenience locations, thank you!

If you found problems commodity information, Welcome to error correction

Operation safe
1． Lamp of positive Pole and Connection of place has Equipment distance any whatguide body 20mm above 。
2． connect touch Lamp of positive Pole and Energy Storage Capacitor positive Pole before certainly use Discharge Device Discharge， accurate recognize no Electric after method can Operation。
3． in no has after over this company Allow of situation below ， not get to Controller and Power Supply of Machine machine structure or Circuitperform more modify ； therefore cause of damage lose this company not negative any what responsibility ！
4． absolutely to not can use Eye direct view out Light window port 。
5． first one point out Light response work Test use ， use free cause person body damage damage 。
WorkingEnvironment
1．Ambient Temperature 20 C ~30 C
2．Relative Humidity not High at 80 %
3．Usage Power Supply Single Phase220V±20％，50Hz
Single Phase110V±10％，60Hz
Run mode
between rest load Continuous Run mode ， use every Continuous Workingten Minute clock between rest ten Minute clock for suitable 。
Coolingstrong system wind cycle Cooling 。
Power Supply week surround response remain 20mm above of empty between 。Guarantee Heat Dissipation and Circuit positive common Working 。

one 、Main Technical Parameters
Supply Voltage：AC220V±20 % AC110V±10 %
Energy Storage Capacitor：100μF/1400V
Input Power：1800W
Output Power：1500W
Output Voltage：DC700-1000V
Remarks：Customizable Output Voltage DC0-1000V of Power Supply。
Match Controller： WK5C2、WK10C

two 、Product Features
adopt Main Power and Pre-ignition Separate design ，Guarantee Product Stable Performance，Suitable at any what Xenon Lamp.
Wiring Simple，Easy Installation，Metal Shell design ， make Power Supply Get more Effective of Protection。
three 、Power Supply Dimensions：
Power Supply meter inch：270*210*130mm( Long * Wide * High )

common see Fault row except

1． press below Working Switch not count number not out Light

this Power Supply place match Controller is accordingto country mark design ， first second out Light has 2Second around of extend h ， so response press live Working Switch not Discharge， etc count number Device count number h immediately can out Light， meanwhile has Prompt sound 。 for done Operation safe ， first one point out Light please Used for Test Machine WorkingStatus， not need direct connect Used for Treatment。

2． press accurate prepare key ，Display Pre-ignition Error

this phenomenon is point Lamp not can success， first need look Lamp is no completegood 。 general via Handpiece Output window immediately can look to ， if Lamp break can look to Lamp has water ， if Lamp leak Gas appearance above is look not out come of 。 can change one Piece new Lamp test one below 。 still has is High Voltage Insulation do of notgood 。 cause High Voltage not enough ， heavy point check Lamp positive Pole of connect Line， especially its is Lamp positive Pole and Power Supply Output Line of Connection division 。 can use three layer heat shrink tube between irrigate input 703glue 。 Lamp Electric Pole distance cavity body of distance also should end maybe far one some ， meanwhile need Insulationgoodgood 。

3． press accurate prepare key ，Systemreturn heavy new Start

this phenomenon is High Voltage Insulation notgood and Interference problem ， first notice Working Switch， end amount Usage pin step Switch， not need Usage Handpiece Switch。

if must Usage Handpiece Switch， please notice Handpiece Switch and cavity body of distance response end maybe far ， same time response add can reliable of Insulation。 then press first two Type situation check 。 meanwhile check High Voltage Output Line distance Control Line etc its it Line response has certainly of distance ， not can all one up walk Line。

4．Display Working ， can count number however not out Light

check Main Power Board stand Board above of Small Lamp is no can bright 。 positive common situation can with out Light yet h bright h extinguish 。 such as not positive common please will row Line two Head to adjust heavy insert ， and check Controller is no for match Set Controller。

phenomenon	check part position
all Machine no Electric	1、 urgent Switch( red color press twist ) is no lift up 。 2、 this Machine Power Supply Plugis no insertgood 。 3、Main Power Road empty Gas Switch is no place at open through position 。 4、 check fuse tube Socket internal fuse tube is no completegood 。 5、Net Power Supply is no has Electric。
no method in input accurate prepare Status	1、 check water Pump is no transport rotate 。 2、 check Coolingwater water position is no over Low。 3、 check Machine is no division at Protection Status。 4、 look Xenon Lamp is no break crack 。 5、 check Handpiece above of connect Line is no has Error。 6、 check Lamp Line positive Pole is no distance its it Circuit over near 。 7、 check Working Switch is no division at close combine Status。
press below Handpiece Switch no Light Output	1、 check System is no in input accurate prepare Status。 2、 check Display is no division at Operation Interface。 3、 check Handpiece Switch is normal 。 4、 check Controller is no has count number 。 5、 check Controller is no in input WorkingStatus。
Light Output clear display change weak	1、 check Net Electric Power Supply is no over Low。 2、 check Output mirror Head is no clean 。 3、 check can amount is no Adjustment over Low。
Controller black screen accompany has buzz Device Alarm	please Measurement Power Supply of 5V supply Electric。