Usage supply Electric Power Supply：220V±20％/50Hz
110V±10％/60Hz
Input Power：300W，700W
Output Power：250W，500W
Energy Storage Capacitor：100~200μF/1400V
most Large WorkingCurrent： 4A peak 20A
fill Electric Voltage： peak 1000V ~1400V
Output Voltage Adjustment：650V~1000V，700V~1400V
Driver Lamp：250W suitable each Type Lamp。500W need match explosion can amount compare Large of Lamp， no then can damage bad Lamp。
Dimensions： LongWide High ：260*146*115mm
Mounting Dimensions：235*102mm
1． Lamp of positive Pole and Connection of place has Equipment distance any whatguide body 20mm above 。
2． connect touch Lamp of positive Pole and Energy Storage Capacitor positive Pole before certainly use Discharge Device Discharge， accurate recognize no Electric after method can Operation。
3． in no has after over this company Allow of situation below ， not get to Controller and Power Supply of Machine machine structure or Circuitperform more modify 。 therefore cause of damage lose this company not negative any what responsibility ！
4. absolutely to not can use Eye direct view out Light window port 。
5． first one point out Light response work Test use ， use free cause person body damage damage 。
1．Ambient Temperature 20 C ~30 C
2．Relative Humidity not High at 80 %
3．Usage Power Supply Single Phase220V±20％，5A，50Hz；Single Phase110V±10％，10A，60HZ。
between rest load Continuous Run mode ， use every Continuous Output10000Pulse between rest 10Minute clock for suitable 。
Coolingstrong system wind cycle Cooling 。
Power Supply week surround response remain 20mm above of empty between 。Guarantee Heat Dissipation and Circuit positive common Working 。
1. press below Working Switch not count number not out Light
this Power Supply place match Controller is accordingto country mark design ， first second out Light has １Second around of extend h ， so response press live Working Switch not Discharge， etc count number Device count number h immediately can out Light， meanwhile has Prompt sound 。 for done Operation safe ， first one point out Light please Used for Test Machine WorkingStatus， not need direct connect Used for Treatment。
2. press accurate prepare key ，Display Pre-ignition Error
this phenomenon is point Lamp not can success， first need look Lamp is no completegood 。 if Lamp break or person leak Gas can change one Piece new Lamp test one below 。 still has is High Voltage Insulation do of notgood 。 cause High Voltage not enough ， heavy point check Lamp positive Pole of connect Line， especially its is Lamp positive Pole and Power Supply Output Line of Connection division 。 can use three layer heat shrink tube between irrigate input 703glue 。 Lamp Electric Pole distance cavity body of distance also should end maybe far one some ， meanwhile need Insulationgoodgood 。 use Handpiece Switch of more need notice Switch of Insulation problem 。
3. press accurate prepare key ，Systemreturn heavy new Start
this phenomenon is High Voltage Insulation notgood and Interference problem ， first notice Working Switch， end amount Usage pin step Switch， not need Usage Handpiece Switch。 if must Usage Handpiece Switch， please notice Handpiece Switch and cavity body of distance response end maybe far ， same time response add can reliable of Insulation。 then press first two Type situation check 。 meanwhile check High Voltage Output Line distance Control Line etc its it Line response has certainly of distance ， not can all one up walk Line。
4.Display Working ， can count number however not out Light
first check Energy Storage Capacitor， then check Main Power Board stand Board above of Small Lamp is no can bright 。 positive common situation can with out Light yet h bright h extinguish 。 such as not positive common please will row Line two Head to adjust heavy insert ，or more change 。 and check Controller is no for match Set Controller(Controller above has J5 character like )。
5. can Display accurate prepare ， however close combine Working Switch， not count number also not out Light。
this phenomenon is Working Switch bad ，or connect Line Fault。 please check Working Switch and connect Line。 such as all positive common please will row Line two Head to adjust heavy insert or more change 。
6. press accurate prepare key Display， please check Working Switch
for done safe ，Machine Settinghas Protection System， press accurate prepare key h ，Working Switch must division at Disconnect Status。 appear this Prompt， please check Working Switch is no lift up ， is no damage bad 。 connect Line is normal 。
7. appear abnormal situation h ， can close drop key Switch， etc 1Minute clock after re- open Machine。
8.about500W Power Supply of Special other Description
this Power Supply has 500W Specification, need will original 250W exc Light Machine modify for 500W System, need notice after over anti again Test and phase response of modify adjust method can Factory, not can Simple change Power Supply done affair 。 first is Lamp， need select use explosion can amount more Large of Lamp， no then Lamp of Lifetime maybe very short 。 additionally cavity body ， four price network ， mirror Sheet， water cycle etc ， all need work phase response of adjust 。 additionally Operation Parameter also need has phase response of adjust ， use reach mostgood of effect ， yet not damage person 。500W/1400V Power Supplygeneral Used for Erbium exc Light。
All Reviews (0)